{"product_id":"emerson-epro-con041-pr6423-00r-111-proximity-sensor-converter","title":"Emerson EPRO CON041 PR6423\/00R-111 Proximity Sensor \u0026 Converter","description":"\u003ch2\u003eEmerson EPRO CON041 \/ PR6423\/00R-111 Proximity System\u003c\/h2\u003e\n\u003cp\u003eThe \u003cstrong\u003eEmerson EPRO CON041\u003c\/strong\u003e signal conditioner combined with the \u003cstrong\u003ePR6423\/00R-111\u003c\/strong\u003e probe, also cataloged as the \u003cstrong\u003e10 mm Eddy-Current Sensor Assembly\u003c\/strong\u003e, operates as a dedicated hardware component for high-precision rotor dynamics and shaft position monitoring within turbomachinery protection platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eCON041 \/ PR6423\/00R-111\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eEmerson EPRO\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eGermany\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e1.0 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e10 mm tip diameter \/ 11 m cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-35 deg C to +180 deg C (Probe)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e24 VDC supply\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMeasurement Range\u003c\/td\u003e\n\u003ctd\u003e2 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch3\u003eEmerson TSI Characteristics\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eCON041\u003c\/strong\u003e system utilizes high-resolution eddy-current probe scaling to convert non-contact shaft displacements into precise electrical outputs. The module executes gap voltage validation, maintaining a -10 VDC baseline for accurate rotor dynamics interpretation. System reliability is further supported by cross-talk suppression, which mitigates signal noise when multiple probes are installed in dense configurations on a bearing housing. The \u003cstrong\u003eCON041\u003c\/strong\u003e module facilitates I\/O density scaling by providing standard 4-20 mA outputs that interface directly with PLC or DCS platforms, while galvanic isolation protects the measurement chain from field-side ground loops and transient electrical surges.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the 11-meter cable length require specific calibration constants in the monitoring system? A: Yes, the CON041\/PR6423 system is factory-calibrated for the specific impedance of the 11-meter integral cable. Users must ensure that the downstream monitoring rack or PLC software uses the corresponding sensitivity coefficient (7.87 mV\/µm) to maintain measurement linearity.\u003c\/p\u003e\n\u003cp\u003eQ: How is the \"OK\/Fault\" relay status utilized in an industrial safety loop? A: The fault relay is internally wired to detect signal clipping, probe disconnection, or power supply loss. This output should be monitored by a digital input card in the host PLC to trigger automatic machine protection sequences or maintenance flags.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eGap Setting:\u003c\/strong\u003e Utilize a precision feeler gauge to establish the nominal gap between the probe tip and the shaft surface, targeting the center of the 0.25–2.25 mm linear range. Verify the gap voltage with a high-impedance multimeter to ensure alignment with the -10 VDC nominal target.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Secure the probe into the mounting bracket using the provided lock nuts. Verify the assembly is rigid to prevent vibration-induced movement during high-speed operation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCabling:\u003c\/strong\u003e Route the 11-meter integral cable through grounded, metallic instrumentation conduit. Ensure the minimum bend radius is maintained and avoid physical contact with high-voltage AC cables to prevent electromagnetic interference.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eValidation:\u003c\/strong\u003e After applying 24 VDC power, observe the \"Sensor OK\" LED on the CON041. A steady LED confirms the probe is detecting the target and the circuit loop is intact.\u003c\/li\u003e\n\u003c\/ol\u003e","brand":"ABB","offers":[{"title":"Default Title","offer_id":43860974927971,"sku":"CON041+PR6423\/00R-111","price":400.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0583\/5246\/8067\/files\/68_094de188-5e2e-43d3-9a9f-2a49916f49eb.jpg?v=1764297744","url":"https:\/\/www.autocontrolglobal.com\/products\/emerson-epro-con041-pr6423-00r-111-proximity-sensor-converter","provider":"AutoControl Global","version":"1.0","type":"link"}