Emerson Ovation 5X00497G01 REV08 Datasheet & Technical Manual
Manufacturer: Emerson
-
Part Number: 5X00497G01 REV08
Condition：New with Original Package
Product Type: Signal Conditioning Modules
-
Country of Origin: USA
Payment:T/T, Western Union
Shipping port: Xiamen
Warranty: 12 months
Emerson 5X00497G01 REV08 Ovation Signal Conditioning Module
The Emerson 5X00497G01 REV08 serves as the primary 5X00497G01 Signal Conditioning Module utilized to execute multi-signal conversion across Emerson Ovation Distributed Control System (DCS) platforms. This revision 08 hardware conditions, linearizes, and digitizes analog and digital execution vectors, routing mixed-signal processing tasks over a unified internal backplane data path.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | 5X00497G01 REV08 |
| Brand | Emerson |
| Origin | USA |
| Weight | 0.5 kg |
| Dimensions | 135 mm x 105 mm x 44 mm |
| Operating Temp | -40 to +85 deg C |
| Power Consumption | 2.5 W typical, 5 W maximum |
| System Compatibility | Emerson Ovation DCS |
| Channel Count | 8 configurable channels |
| Signal Typology | AI, AO, DI, DO, HART |
| Internal Conversion | 16-bit resolution |
| Isolation Voltage | 1500 V DC channel-to-channel |
| Calibration Accuracy | +/-0.05% Full Scale |
| Operating Input Voltage | 24 VDC +/-10% |
| Network Protocols | FOUNDATION Fieldbus, HART |
| Storage Temperature | -20 to +85 deg C |
| Humidity Range | 10% to 90%, non-condensing |
| Safety/Hazardous Rating | SIL3 (IEC 61508), ATEX Zone 1, CE |
Process Control and DCS Instrument Integration
The module implements 1500 V DC channel-to-channel isolation networks to decouple every signal path from adjacent wiring paths and internal backplane logic. When field channels are configured to process the 4-20 mA HART loop protocol layer or interface with FOUNDATION Fieldbus segments, the integrated 16-bit converters filter out high-frequency electrical transients and common-mode noise voltages. This hardware design maintains analog-to-digital measurement accuracy within a +/-0.05% full-scale boundary limit under high electromagnetic interference conditions.
Frequently Asked Questions
Q: How is the mixed-signal logic configured on individual channels of the 5X00497G01 REV08?
A: The configuration of the eight channels for analog or digital execution (AI, AO, DI, DO) is controlled via Ovation software tools. Internal electronic switches modify the termination impedance and signal pathways within the conditioning matrix based on the downloaded system database parameters.
Q: What are the restrictions regarding the SIL3 certification during active operations?
A: The hardware achieves functional compliance with SIL3 parameters according to IEC 61508 protocols. To maintain this hardware classification during maintenance states, internal diagnostic routines continuously report failure fractions to the Ovation controller over the backplane bus, ensuring fail-safe state execution bounds are preserved.
Field Installation Guidelines
- Chassis Earth and Carrier Grounding: Mount the module assembly firmly into its assigned slot on the Ovation I/O carrier. Connect the integrated chassis ground rail directly to the plant copper instrument ground grid using an unpainted, low-impedance conductor maintaining a resistance parameter under 1 Ohm.
- ATEX Zone 1 Enclosure Requirements: For installations deployed within certified ATEX Zone 1 hazardous areas, the module must be mounted inside a purged or intrinsically safe industrial enclosure with a protection rating of at least IP54. Field terminals must not be worked on while the 24 VDC supply line is active.
- Cable Shielding and Isolation: Terminate the cable drain wires from field instruments at the marshaling side terminal earth bar only. Do not ground the shielding at the sensor housing to prevent earth loop currents from distorting the 16-bit analog sampling logic.