GE IC200GBI001-GJ VersaMax Genius Network Interface Module
Manufacturer: GE Fanuc
-
Part Number: IC200GBI001-GJ
Condition：New with Original Package
Product Type: Bus Interface Modules
-
Country of Origin: USA
Payment:T/T, Western Union
Shipping port: Xiamen
Warranty: 12 months
GE Fanuc IC200GBI001-GJ VersaMax Genius Network Interface Module
Configured for distributed field bus expansion in Genius I/O networks, the GE Fanuc IC200GBI001-GJ (IC200GBI001 Bus Interface Module) provides direct physical/electrical execution. The module links VersaMax I/O station racks directly to a Genius serial bus, managing serial network data exchange across designated controller address ranges.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | IC200GBI001-GJ |
| Brand | GE Fanuc / Emerson |
| Origin | Refer to device label |
| Weight | 0.17 kg (0.38 lbs) |
| Dimensions | 120 mm x 90 mm x 40 mm |
| Operating Temp | 0 deg C to +60 deg C |
| Power Consumption | +5 VDC @ 250 mA, +3.3 VDC @ 10 mA |
| Communication Network | Genius I/O bus |
| Serial Bus Address Range | 0 to 31 |
| Transmission Rates | 153.6 kbaud (extended); 153.6 kbaud, 76.8 kbaud, 38.4 kbaud (standard) |
| Module Capacity | Up to 8 modules per rack, up to 8 racks total |
| Memory Limits | 1024 discrete inputs, 1024 discrete outputs, 128 bytes analog I/O |
| Network Scan Capacity | 128 bytes input / 128 bytes output per bus scan |
| Terminating Resistors | Selectable 75, 100, 120, or 150 ohms |
| Compatible Controllers | PACSystems RX3i, PACSystems RX7i, Series 90-70 |
Backplane Bus Communication Velocity & Network Execution
The network interface module coordinates backplane bus communication velocity across attached VersaMax I/O carriers to maintain rapid I/O scan synchronization. Internal logic decodes data frames from Series 90-70 or PACSystems controllers and transfers discrete and analog states across the backplane bus within tight update windows. Firmware flash compatibility supports uniform hardware handshaking and preserves deterministic response times during multi-rack field scans.
Frequently Asked Questions
Q: How is physical line termination applied on the Genius serial network trunk?
A: The module supports software-selectable or jumper-configured terminating resistor values of 75, 100, 120, or 150 ohms at both physical ends of the daisy-chain network segment to prevent signal reflections.
Q: What power rails must the VersaMax carrier supply to operate this module?
A: The backplane must supply two DC voltage levels: +5 VDC drawing up to 250 mA and +3.3 VDC drawing up to 10 mA for low-voltage communication logic circuits.
Q: How many local I/O modules can a single Genius bus interface manage?
A: The interface manages up to 8 I/O modules per rack and scales across up to 8 connected racks, supporting up to 2048 total discrete points (1024 inputs / 1024 outputs) and 128 bytes of analog memory.
Field Installation Guidelines
- Secure the network interface unit onto a standard 35 mm DIN rail or panel subplate using the primary slot of the VersaMax baseplate.
- Wire the dual Genius bus terminals in a sequential daisy-chain topology using shielded twisted-pair communication cable.
- Connect the cable drain wire to the earth ground tab on the terminal block to establish optical isolation and shield protection against industrial electrical noise.
- Verify that the serial bus address (0 to 31) and baud rate match the host controller hardware configuration prior to applying bus power.