HE693PBM101 GE Series 90-30 PROFIBUS-DP Master Module
Manufacturer: GE Fanuc
-
Part Number: HE693PBM101
Condition：New with Original Package
Product Type: Communication Modules
-
Country of Origin: USA
Payment:T/T, Western Union
Shipping port: Xiamen
Warranty: 12 months
GE Fanuc HE693PBM101 Series 90-30 PROFIBUS-DP Master Module
The GE Fanuc HE693PBM101, also cataloged as the HE693PBM101 PROFIBUS-DP Master Module, operates as a dedicated hardware component for cyclic data exchange and slave device management within GE Fanuc Series 90-30 PLC backplane racks. The card handles up to 125 field nodes across a 9-pin D-sub interface using EN 50170 standard framing protocols. It draws operational voltage directly through the internal 5 VDC power bus.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | HE693PBM101 |
| Brand | GE Fanuc |
| Origin | USA |
| Weight | 0.45 kg |
| Dimensions | 132 x 36 x 152 mm |
| Operating Temp | 0 deg C to +60 deg C |
| Power Consumption | 500 mA at 5 VDC (backplane draw) |
| Protocol | PROFIBUS-DP (Class 1 Master, EN 50170) |
| Baud Rates | 9.6 kbps to 12 Mbps (with auto-baud detection) |
| Maximum Devices | 125 DP slave devices |
| Network Distance | Up to 1200 m at 9.6 kbps (shorter at higher baud rates) |
| Physical Interface | Standard 9-pin female D-sub connector |
| Diagnostic Status | Front-panel LEDs (Module OK, Bus Activity, Fault) |
| Rack Slot Requirement | Single-slot mount on Series 90-30 baseplate |
Backplane Bus Interface and Data Throughput
The module communicates with the CPU using the parallel backplane bus architecture of the Series 90-30 rack system. Backplane bus communication velocity remains synchronized with the main processor scan cycle to avoid I/O transfer latency. Furthermore, the internal firmware flash compatibility ensures direct firmware handshakes with Proficy Machine Edition and Logicmaster 90 programming software. The physical channel establishes deterministic data delivery down to sub-millisecond ranges when running at maximum 12 Mbps transmission speeds, maintaining hardware buffer integrity across dense multi-node subnetworks.
Frequently Asked Questions
Q: What is the backplane current draw requirement for the HE693PBM101 module?
A: The module draws approximately 500 mA to 600 mA directly from the 5 VDC power bus on the Series 90-30 backplane rack during full communication throughput.
Q: How does the master module detect device speeds on an active PROFIBUS network?
A: The onboard controller executes automatic baud rate detection across the supported spectrum from 9.6 kbps up to 12 Mbps, matching the pre-configured speed of the network bus during initialization.
Field Installation Guidelines
Install the HE693PBM101 module into a standard single slot on any Series 90-30 baseplate while the rack power is completely switched off. First, insert the top hook of the module housing into the rack notch, then firmly press the bottom edge until the rear backplane connector seats completely. Tighten the retaining screw at the bottom of the module to lock it into place against high-vibration field environments.
Always route the PROFIBUS-DP network cable using shielded twisted-pair wire designated for RS-485 differential signaling. Terminate the shield braid directly to ground at both ends using low-impedance grounding clamps. When attaching the 9-pin D-sub connector, ensure that the active line termination switches are set to "ON" only at the physical end nodes of the segment. Keep signal cables physically separated from high-voltage AC power lines by a minimum distance of 200 mm to suppress transient electromagnetic interference.