IC200GBI001 GE Fanuc VersaMax Genius Network Interface Module
Manufacturer: GE Fanuc
-
Part Number: IC200GB1001
Condition：New with Original Package
Product Type: Communication Modules, Network Interface Units
-
Country of Origin: USA
Payment:T/T, Western Union
Shipping port: Xiamen
Warranty: 12 months
GE Fanuc IC200GBI001 VersaMax Genius Network Interface Unit
The GE Fanuc IC200GBI001-LL, also cataloged as the IC200GBI001 Genius Network Interface Unit, operates as a dedicated hardware component for protocol translation and fieldbus data routing within GE VersaMax PLC platforms. Field engineers seat the unit onto the VersaMax backplane carrier where it bridges up to eight local I/O expansion modules directly to a Genius network highway. The interface converts internal rack backplane data into serial Genius bus transactions, which enables deterministic data exchange across up to 32 network nodes at selectable baud rates.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | IC200GBI001-LL / IC200GBI001 |
| Brand | GE Fanuc |
| Origin | USA / Standard Industrial Sourcing |
| Weight | 0.45 kg (1.00 lbs) |
| Dimensions | 66.8 x 128 x 130 mm (2.63 x 5.04 in) |
| Operating Temp | 0 to 60 deg C |
| Power Consumption | 1.5 W (5 VDC at 250 mA, 3.3 VDC at 10 mA from backplane) |
| Bus Type | Genius I/O bus (Daisy-chain topology) |
| Transmission Rates | 153.6 kbaud, 76.8 kbaud, 38.4 kbaud |
| Maximum Nodes | Up to 32 Genius devices (Addresses 0 to 31) |
| System Capacity | 8 modules per rack, up to 128 bytes input/output bus scan |
| I/O Memory Limits | 1024 discrete inputs, 1024 discrete outputs, 128 bytes analog I/O |
| Terminating Resistors | Selectable 75, 100, 120, or 150 ohms |
Backplane Bus Communication Velocity and System Integration
The network interface unit maintains high backplane bus communication velocity while multiplexing discrete and analog signals across expanded VersaMax sub-racks. Internal logic processing maps up to 2048 discrete points directly to deterministic networks running the Genius serial protocol, preventing data latencies across distributed control loops. Complete firmware flash compatibility across attached VersaMax I/O modules maintains synchronized execution, allowing seamless integration with Series 90-70, PACSystems RX3i, and PACSystems RX7i controllers.
Frequently Asked Questions
Q: How do operators configure the Genius serial bus address on the IC200GBI001 module?
A: Technical personnel set the serial bus address within the range of 0 to 31 using onboard DIP switches or through software setup before establishing network communication.
Q: What bus termination resistance values does the module interface support?
A: Installers configure terminating resistors of 75, 100, 120, or 150 ohms at both physical ends of the daisy-chain network segment to prevent signal reflections and line impedance mismatch.
Q: Can the IC200GBI001 supply loop power to external Genius field I/O devices?
A: The module draws power directly from the 5 VDC VersaMax backplane rail to run internal logic and communication hardware, requiring external field power sources for attached field devices.
Field Installation Guidelines
Execute the following sequential installation steps inside the control enclosure:
- Turn off all main power sources supplying the VersaMax rack and field devices before inserting the module.
- Slide the interface module into the leftmost carrier slot until the mechanical backplane connectors latch securely.
- Wire the Genius serial bus cable using twisted-shielded pair conductors, connecting terminals in a continuous daisy-chain topology without stubs.
- Attach a matching termination resistor across the bus lines at both physical end nodes of the Genius network segment.
- Connect all cable drain shields directly to the cabinet ground bar using short copper grounding leads, then apply power to check front panel status LEDs.