IC200PBI001-FF GE PROFIBUS-DP Network Interface Unit
Manufacturer: GE Fanuc
-
Part Number: IC200PBI001-FF
Condition：New with Original Package
Product Type: Network Interface Modules
-
Country of Origin: USA
Payment:T/T, Western Union
Shipping port: Xiamen
Warranty: 12 months
GE IC200PBI001-FF VersaMax PROFIBUS-DP Network Interface Unit
Configured for fieldbus communication and remote I/O data routing in VersaMax platforms, the GE Fanuc IC200PBI001-FF (IC200PBI001 Network Interface Unit) provides direct physical/electrical execution. The hardware module operates as a PROFIBUS-DP slave device, linking up to 8 VersaMax I/O expansion modules directly to a primary PROFIBUS master controller over a linear bus topology. It converts backplane I/O process signals into standard PROFIBUS telemetry at auto-detected data rates ranging from 9.6 kbps to 12 Mbps.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | IC200PBI001-FF |
| Brand | GE Fanuc / Emerson |
| Origin | USA |
| Weight | 0.31 kg |
| Dimensions | Standard VersaMax NIU Form Factor |
| Operating Temp | 0 to 60 deg C |
| Power Consumption | 5 VDC at 250 mA; 3.3 VDC at 10 mA (Backplane-supplied) |
| Network Protocol | PROFIBUS-DP (Slave) |
| Baud Rate | 9.6 kbps to 12 Mbps (Auto-detected) |
| Maximum I/O Data | 375 bytes total (Up to 244 bytes inputs or outputs) |
| Network Connector | 9-pin D-sub female |
| Addressing Range | 0 to 125 (Configurable via onboard rotary switches) |
| Expansion Capacity | Controls up to 8 I/O modules per station |
| Signal Isolation | 1500 V RMS fieldbus to logic |
Backplane Bus Communication Velocity and Firmware Compatibility
The network interface unit executes cyclic I/O data exchanges across the local carrier plane, maintaining backplane bus communication velocity while transferring up to 375 bytes of process data to the host master. Onboard hardware registers validate module firmware flash compatibility during rack boot sequences, ensuring structured bit-mapping across connected expansion cards. Internal memory buffers hold up to 5 bytes of standard PROFIBUS diagnostic telemetry along with 2 bytes of station control data for continuous network reporting.
Frequently Asked Questions
Q: How do technicians configure the PROFIBUS station address on this module?
A: The station address is assigned using physical rotary switches located on the module housing, supporting valid bus address selections from 0 to 125 without requiring external software tools during initial bench staging.
Q: What transmission media and cabling rules apply when operating at the maximum 12 Mbps baud rate?
A: High-speed operation requires shielded twisted-pair Type A PROFIBUS cable with active bus terminations at both physical ends of the line segment. Spurious stubs must be strictly avoided at 12 Mbps to prevent signal reflections and data frame corruption.
Q: What front panel LED indicators assist with network troubleshooting?
A: The module provides an OK LED to indicate internal backplane logic status, a Network LED to display active PROFIBUS-DP communication states, and dedicated Module Status LEDs to flag local expansion rack errors.
Field Installation Guidelines
Mount the network interface unit onto a VersaMax I/O carrier fixed to a grounded 35 mm DIN rail inside an industrial control enclosure. Slide the module vertically onto the carrier guide tracks until the rear backplane connector seats completely and the locking latches engage. Connect the standard 9-pin D-sub PROFIBUS cable connector to the front port and tighten the retention thumbscrews.
Route shielded PROFIBUS communication cables through grounded metal raceways separated by at least 200 mm from high-voltage AC conductors and motor drive cabling. Ensure cable shields are bonded directly to the cabinet ground bar at the point of cable entry. De-energize all field and rack power sources prior to inserting or removing the module in Class I, Div 2 hazardous environments.