IC693PWR324 GE Fanuc Power Supply Module | New & Original Stock
Manufacturer: GE Fanuc
-
Part Number: IC693PWR324/Z
Condition：New with Original Package
Product Type: Power Supply Modules
-
Country of Origin: USA
Payment:T/T, Western Union
Shipping port: Xiamen
Warranty: 12 months
GE Fanuc IC693PWR324 Series 90-30 Power Supply Module
The GE Fanuc IC693PWR324, also cataloged as the IC693PWR324 Power Supply Module, operates as a dedicated hardware component for supplying regulated DC power to CPU and I/O modules within Series 90-30 PLC platforms.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | IC693PWR324 |
| Brand | GE Fanuc / Emerson |
| Origin | USA |
| Weight | 0.40 kg (0.88 lbs) |
| Dimensions | Standard Series 90-30 rack form factor |
| Operating Temp | 0 to 60 deg C |
| Power Consumption | 90 VA maximum input / 30 Watts output capacity |
| Input Voltage Range | 100-240 Volts AC (Nominal 120/240 VAC auto-ranging) / 125 VDC |
| Input Frequency Range | 47-63 Hz |
| Internal DC Outputs | +5 VDC, +12 VDC, -12 VDC |
| Max Output Current | +5 VDC @ 3.0 A; +12 VDC @ 2 A; -12 VDC @ 1 A |
| Auxiliary Relay Output | 24 VDC |
| Max Inrush Current | 4 Amperes maximum |
| Isolation Voltage | 1500 VAC |
| Ripple / Noise | 50 mV |
| Diagnostic Interface | Integrated RS-485 serial port |
| Status Displays | 4 LEDs for power status and fault tracking |
| Storage Temp | -40 to 85 deg C |
Backplane Bus Performance & Firmware Flash Compatibility
The IC693PWR324 mounts directly into the left-hand slot of standard Series 90-30 baseplates, supplying filtered DC rails across the internal copper distribution lines. The output stages regulate load fluctuations to prevent ripple voltage from degrading backplane bus communication velocity during peak I/O execution.
While the power supply operates as an analog and switching component, full coordination with intelligent modules requires proper firmware flash compatibility across the rack. Unstable logic voltage caused by exceeding the 30 Watt barrier can corrupt the memory flash sequence on adjacent CPU or network modules, resulting in system startup interlocks or communication dropping across the local RS-485 serial network.
Frequently Asked Questions
Q: How does the IC693PWR324 handle thermal overloads and short circuits?
A: The module features integrated electronic overvoltage, overcurrent, and thermal protection circuits. If a field-side wiring fault or severe overtemperature condition occurs, the module shuts down the internal DC voltage rails to safeguard the connected processing units and registers the event on the diagnostic LEDs.
Q: Can this power supply module be hot-swapped while the rack is active?
A: No. The Series 90-30 baseplate architecture does not permit hot-swapping. The incoming AC line power must be physically disconnected and locked out prior to removing or installing the power supply module to prevent electrical arcing across the backplane terminals.
Q: What is the function of the integrated RS-485 serial port on the power supply casing?
A: The serial port provides a direct hardware link to the CPU's programming and configuration services when the module is seated in the rack. This port facilitates connection to local programmer units or human-machine interfaces using SNP protocols.
Field Installation Guidelines
- Baseplate Engagement: Ensure the main AC power distribution block is de-energized. Slide the power supply housing into the dedicated left slot of the baseplate, ensuring the rear tabs lock into the chassis frame before tightening the mechanical retention screws.
- Line Power Grounding: Connect the incoming AC lines (120/240 VAC) using wire gauges sized for the maximum inrush specifications. Terminate the safety ground conductor directly to the dedicated ground screw on the module terminal strip.
- Conduit Segregation: Route the incoming high-voltage AC power lines away from the low-voltage DC I/O wiring and RS-485 communication lines to prevent induced electrical noise from entering the backplane electronics.
- Convection Spacing: Maintain standard vertical and horizontal clearance boundaries around the Series 90-30 rack structure to permit ambient air to rise freely through the lower and upper ventilation slots of the module housing.