IC695ETM001-CC GE Fanuc PACSystems RX3i Ethernet Module
Manufacturer: GE Fanuc
-
Part Number: IC695ETM001-CC
Condition：New with Original Package
Product Type: Ethernet Interface Modules
-
Country of Origin: USA
Payment:T/T, Western Union
Shipping port: Xiamen
Warranty: 12 months
GE Fanuc IC695ETM001-CC PACSystems RX3i Ethernet Interface Module
The GE Fanuc IC695ETM001-CC, also cataloged as the IC695ETM001 Ethernet Interface Module, operates as a dedicated hardware component for high-speed network communications and protocol routing within PACSystems RX3i platforms. Driven by an onboard 200 MHz Ethernet processor, the single-slot module manages dual 10/100 Mbps auto-sensing channels alongside a front-panel RS-232 serial port. It handles determinism across distributed I/O architectures while executing SRTP, Modbus/TCP, and Ethernet Global Data (EGD) exchange operations directly over the local backplane.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | IC695ETM001-CC |
| Brand | GE Fanuc |
| Origin | United States |
| Weight | 0.25 kg (0.55 lbs) |
| Dimensions | 3.8 cm x 13.5 cm x 14.0 cm |
| Operating Temp | 0 to 60 deg C |
| Power Consumption | 2.5 W (500 mA @ 5 VDC) |
| Ethernet Ports | 2 x 10/100 Mbps (RJ45, half/full duplex) |
| Processor Speed | 200 MHz |
| Serial Interface | 1 x RS-232 (9-pin D-sub, 1200 to 115200 bps) |
| Network Protocols | SRTP, Modbus/TCP, EGD, SNMP |
| Max Connections | 32 SRTP client/server connections |
| EGD Capability | Up to 256 exchanges |
Backplane Bus Communication and Network Velocity
The IC695ETM001-CC interfaces directly with the high-speed PACSystems RX3i PCI backplane bus, offloading network protocol processing from the main system CPU. Through its dual 10/100 Mbps shielded RJ45 interfaces, the module supports non-volatile memory buffering to maintain deterministic packet transmission during heavy network loads. Onboard firmware firmware flash compatibility ensures seamless backplane bus communication velocity and clock synchronization when exchanging 256 EGD data blocks or handling up to 32 simultaneous SRTP client and server connections across process networks.
Frequently Asked Questions
Q: Does the IC695ETM001-CC support hot-swapping inside a live RX3i rack?
A: Yes, the module supports Hot Swap (Insertion/Removal Under Power) capabilities on the RX3i PCI backplane without interrupting controller execution or disturbing adjacent module communications, provided proper field wiring safety precautions are observed.
Q: Can the dual Ethernet ports on the front panel be assigned separate IP addresses?
A: No, the two RJ45 connectors route through an internal switch fabric sharing a unified IP address and MAC layer, allowing maintenance technicians to daisy-chain Ethernet nodes without installing an external industrial switch.
Q: What is the power draw requirement for the IC695ETM001-CC from the backplane?
A: The module draws approximately 500 mA at 5 VDC directly from the RX3i backplane power supply, consuming a nominal 2.5 W during standard full-duplex transmission loops.
Field Installation Guidelines
Verify that the rack power supply capacity covers the additional 500 mA current draw at 5 VDC before inserting the IC695ETM001-CC into any available universal expansion slot on the RX3i backplane. Align the module card edge with the backplane guide rails and press firmly until the top and bottom retention levers snap securely into place.
Route standard STP Category 5e or Category 6 cables into the dual RJ45 connectors, ensuring the metal shielding of the connector mates tightly with the module port frame. Ground the overall cable shield at the entry point of the enclosure to suppress high-frequency noise. Maintain a minimum distance of 20 cm between communication wiring and high-voltage AC lines to preserve signal integrity and minimize packet retries across the network.